Decking for a 8 × 32 ft deck in 5/4 × 6 treated, straight layout

5/4 × 6 pressure-treated boards

38× 20 ft

18 rows across 8 ft — 605 linear ft including 5% waste

Boards to buy	38× 20 ft
Linear feet576 ft plus 5% waste	605ft
Rows of decking8 ft ÷ 5.625″ repeat	18rows
Board repeat5.5″ actual width + 0.125″ gap — not the nominal size	5.625in
Deck area8 × 32 ft	256ft²
Joists crossedat 24″ o.c. over 32 ft	17joists
Deck screwstwo per board-joist crossing — about 2 boxes of 350	612screws
Layoutboards run perpendicular to the joists — least waste	straight
Butt joints32 ft run exceeds the 20 ft board — stagger the joints and land every one on a joist	Yes

Deck width: 8 ft
Deck length: 32 ft
Board: 5/4 × 6 treated
Layout: straight
Joist spacing: 24 in o.c.

Nominal width is not actual width

This is where board counts go wrong. A 5/4 × 6 treated board measures its real width, and with the gap it needs the repeat is 5.625″ — which is what actually decides the row count.

8 ft of deck at that repeat is 18 rows, and 38 boards once 5% waste for the straight layout is added.

Working from the nominal size undercounts by close to a tenth.

The gap is not optional in either direction

Treated lumber is sold wet and shrinks. Composite expands with heat. Gap too tight on composite and it buckles in July; gap too wide on wet treated lumber and by autumn you have gaps that swallow a phone.

Screws

612 — two at every board-joist crossing, across 17 joists. One screw per crossing lets the board cup and lift at the corner, and that is the single most common reason a deck looks tired after two summers.

Read the end grain

Lay boards bark-side up. A board cups away from its bark side, so bark-up sheds water off the crown rather than holding it in a trough.

Butt joints

Where the run exceeds a standard board length, stagger the joints so no two adjacent rows meet over the same joist — and double the joist under every joint. A butt joint on a single joist gives each board about ¾ inch of bearing, which is not enough for either board.

Notes

**Nominal width is not actual width.** A "5/4 ×" board measures 5.5″ across. With a 0.125″ gap the repeat is 5.625″, which is what decides the row count — 18 rows here. Working from the nominal size undercounts by close to a tenth.
Sold wet — it shrinks, so gap it tight at about ⅛″. The gap is not optional in either direction: too tight on composite and it buckles in July; too wide on wet treated lumber and you get gaps you can drop a phone through by autumn.
Straight layout, 5% waste — boards run perpendicular to the joists — least waste. This is the least wasteful way to lay a deck, and the fastest.
The 32 ft run is longer than a 20 ft board, so there will be butt joints. Stagger them so no two adjacent rows join over the same joist, and double the joist under every joint — a butt joint on a single joist gives each board about ¾″ of bearing.
Fasten with two screws at every board-joist crossing — 612 screws here. One screw lets the board cup and lift at the corner, and it is the single most common reason a deck looks tired after two summers.
Lay the boards bark-side up if you can read the end grain. A board cups away from the bark side, so bark-up sheds water off the crown instead of holding it in a trough.

Nearby sizes

How Many Footings Does a Deck Need? Work Backwards From Tributary AreaNobody decides footing count directly. It falls out of how far the beam can span, and how much deck each post is holding up.
Cost to Build a Deck per Square Foot: Where the Money Actually GoesDecking boards are the part everyone shops for and about a quarter of the bill. The framing underneath is where the price is decided.
Ledger Attachment: The Detail That Causes Nearly Every Deck CollapseSpan tables get the attention. Ledger failure is what actually drops decks, and it is almost always one of four specific mistakes.
Deck Joist Span Tables: The Four Assumptions That Have to HoldThe span table is not a rule about lumber. It is a rule about lumber carrying 40 psf, dry, at No. 2 grade, with no cantilever, and any of those can be false on your deck.