Decking for a 26 × 18 ft deck in cedar, herringbone layout

5/4 × 6 cedar boards

66× 20 ft

55 rows across 26 ft — 1,188 linear ft including 20% waste

Boards to buy	66× 20 ft
Linear feet990 ft plus 20% waste	1,188ft
Rows of decking26 ft ÷ 5.688″ repeat	55rows
Board repeat5.5″ actual width + 0.1875″ gap — not the nominal size	5.688in
Deck area26 × 18 ft	468ft²
Joists crossedat 16″ o.c. over 18 ft	14joists
Deck screwstwo per board-joist crossing — about 5 boxes of 350	1,540screws
Layouttwo cuts on most boards and offcuts that fit nothing	herringbone
Butt joints20 ft boards cover the 18 ft run in one piece	None needed

Deck width: 26 ft
Deck length: 18 ft
Board: cedar
Layout: herringbone
Joist spacing: 16 in o.c.

Nominal width is not actual width

This is where board counts go wrong. A cedar board measures its real width, and with the gap it needs the repeat is 5.688″ — which is what actually decides the row count.

26 ft of deck at that repeat is 55 rows, and 66 boards once 20% waste for the herringbone layout is added.

Working from the nominal size undercounts by close to a tenth.

The gap is not optional in either direction

Treated lumber is sold wet and shrinks. Composite expands with heat. Gap too tight on composite and it buckles in July; gap too wide on wet treated lumber and by autumn you have gaps that swallow a phone.

Screws

1,540 — two at every board-joist crossing, across 14 joists. One screw per crossing lets the board cup and lift at the corner, and that is the single most common reason a deck looks tired after two summers.

Read the end grain

Lay boards bark-side up. A board cups away from its bark side, so bark-up sheds water off the crown rather than holding it in a trough.

Butt joints

Where the run exceeds a standard board length, stagger the joints so no two adjacent rows meet over the same joist — and double the joist under every joint. A butt joint on a single joist gives each board about ¾ inch of bearing, which is not enough for either board.

Notes

**Nominal width is not actual width.** A "5/4 ×" board measures 5.5″ across. With a 0.1875″ gap the repeat is 5.688″, which is what decides the row count — 55 rows here. Working from the nominal size undercounts by close to a tenth.
Sold dry, so it gaps wider than treated lumber. The gap is not optional in either direction: too tight on composite and it buckles in July; too wide on wet treated lumber and you get gaps you can drop a phone through by autumn.
Herringbone layout, 20% waste — two cuts on most boards and offcuts that fit nothing. Order the full allowance in one go; diagonal offcuts rarely fit anywhere else on the deck.
A 20 ft board covers the 18 ft run in one piece. Worth paying for: an unbroken board is stronger, drains better and looks like a deck rather than a repair.
Fasten with two screws at every board-joist crossing — 1,540 screws here. One screw lets the board cup and lift at the corner, and it is the single most common reason a deck looks tired after two summers.
Lay the boards bark-side up if you can read the end grain. A board cups away from the bark side, so bark-up sheds water off the crown instead of holding it in a trough.

Nearby sizes

Deck Screws per Square Foot: The Count, the Length, and the Coating That MattersRoughly 350 screws per hundred square feet at standard spacing — and the coating rating matters more to the deck's life than the count does.
Cost to Replace Deck Boards Only: When Resurfacing Beats RebuildingResurfacing saves roughly half the cost of a rebuild, provided the frame underneath has more life left than the boards you are about to screw to it.
Hidden Deck Fasteners or Face Screws: Cost, Speed, and the Repair ProblemHidden fasteners cost roughly three times as much and look better. The question that decides it is what happens when one board in the middle needs to come out.
Deck Board Gap: Why Wet Lumber and Composite Need Opposite NumbersThere is no single correct gap. There is a correct gap for a board that is going to shrink and a different one for a board that is going to grow.