How many deck boards for a 30 × 14 ft deck?

5/4 × 6 cedar boards

68× 16 ft

64 rows across 30 ft — 941 linear ft including 5% waste

Boards to buy	68× 16 ft
Linear feet896 ft plus 5% waste	941ft
Rows of decking30 ft ÷ 5.688″ repeat	64rows
Board repeat5.5″ actual width + 0.1875″ gap — not the nominal size	5.688in
Deck area30 × 14 ft	420ft²
Joists crossedat 12″ o.c. over 14 ft	15joists
Deck screwstwo per board-joist crossing — about 6 boxes of 350	1,920screws
Layoutboards run perpendicular to the joists — least waste	straight
Butt joints16 ft boards cover the 14 ft run in one piece	None needed

Notes

Nominal width is not actual width. A "5/4 ×" board measures 5.5″ across. With a 0.1875″ gap the repeat is 5.688″, which is what decides the row count — 64 rows here. Working from the nominal size undercounts by close to a tenth.
Sold dry, so it gaps wider than treated lumber. The gap is not optional in either direction: too tight on composite and it buckles in July; too wide on wet treated lumber and you get gaps you can drop a phone through by autumn.
Straight layout, 5% waste — boards run perpendicular to the joists — least waste. This is the least wasteful way to lay a deck, and the fastest.
A 16 ft board covers the 14 ft run in one piece. Worth paying for: an unbroken board is stronger, drains better and looks like a deck rather than a repair.
Fasten with two screws at every board-joist crossing — 1,920 screws here. One screw lets the board cup and lift at the corner, and it is the single most common reason a deck looks tired after two summers.
Lay the boards bark-side up if you can read the end grain. A board cups away from the bark side, so bark-up sheds water off the crown instead of holding it in a trough.

Nominal width is not actual width

This is where board counts go wrong. A cedar board measures its real width, and with the gap it needs the repeat is 5.688″ — which is what actually decides the row count.

30 ft of deck at that repeat is 64 rows, and 68 boards once 5% waste for the straight layout is added.

Working from the nominal size undercounts by close to a tenth.

The gap is not optional in either direction

Treated lumber is sold wet and shrinks. Composite expands with heat. Gap too tight on composite and it buckles in July; gap too wide on wet treated lumber and by autumn you have gaps that swallow a phone.

Screws

1,920 — two at every board-joist crossing, across 15 joists. One screw per crossing lets the board cup and lift at the corner, and that is the single most common reason a deck looks tired after two summers.

Read the end grain

Lay boards bark-side up. A board cups away from its bark side, so bark-up sheds water off the crown rather than holding it in a trough.

Butt joints

Where the run exceeds a standard board length, stagger the joints so no two adjacent rows meet over the same joist — and double the joist under every joint. A butt joint on a single joist gives each board about ¾ inch of bearing, which is not enough for either board.

Nearby sizes

Deck Cost by State — Priced From BLS Carpenter PayDeck quotes vary more within a town than between states, and this table shows why: carpenter pay ranges 45% across the country but only lands on 55% of the bill.
Deck Screws per Square Foot: The Count, the Length, and the Coating That MattersRoughly 350 screws per hundred square feet at standard spacing — and the coating rating matters more to the deck's life than the count does.
Cost to Replace Deck Boards Only: When Resurfacing Beats RebuildingResurfacing saves roughly half the cost of a rebuild, provided the frame underneath has more life left than the boards you are about to screw to it.
Deck Board Gap: Why Wet Lumber and Composite Need Opposite NumbersThere is no single correct gap. There is a correct gap for a board that is going to shrink and a different one for a board that is going to grow.